產品詳情內容介紹
Kollmorgen 6SM77K-3.000-G-J-09-HA-IN伺服電動機
靜電放電意識使用或靠近控制裝置時，請遵循這些預防措施。
1.不穿衣服，避免身體上積聚靜電由合成材料制成。
盡量穿棉質或棉混紡材料盡可能的，因?yàn)樗鼈儾粌Υ婺敲炊嗟撵o電合成材料。
2.不要從控制柜上拆下印刷電路板（PCB）除非絕對必要。如果必須從控件中卸下PCB機柜，請遵循以下預防措施：? 請勿觸摸PCB的任何部分，邊緣除外。
? 不要觸摸電導體、連接器或用導電設備或用手操作的部件。
? 更換PCB時，請將新PCB保持在塑料防靜電中在您準備好安裝之前，它會一直放在保護袋中。
立即從控制柜中卸下舊PCB后，將其放在防靜電保護袋。
安全使用的特殊條件需要安裝固定接線。
現場接線必須符合北美I級2區（CEC和NEC）或歐洲2區，適用的3類接線方法，并符合當?shù)鼐哂泄茌牂?quán)的檢驗機構。
現場接線必須適合在高于環境溫度至少10°C的條件下進行活動
505數字控制需要使用PE端子接地
A開關或斷路器應包括在關閉的建筑安裝中靠近設備且操作員易于接近。
開關或斷路器應清楚標記為設備開關或斷路器不得中斷保護接地（PE）導線。
505數字控制適用于歐洲2區IIC組安裝在IP54最低額定外殼中時的環境60079-0和EN 60079-15。
該設備必須安裝在一個足夠的區域或外殼內防止大于2焦耳的沖擊和灰塵或水進入。
對于ATEX/IECEx，505數字控制應安裝在一個外殼內，該外殼編碼Ex nA，最低防護等級為IP54。
安裝人員應確保最高周圍空氣溫度不超過額定值最終安裝位置的溫度為+70°C。
505數字控制不得安裝在IEC規定的污染等級超過2級的區域60664-1.正常操作時，不得接近外殼內部不使用工具。
本手冊介紹了汽輪機的伍德沃德505數字調速器帶單量程或分量程執行器。
發布版本為8200-1300，8200-1301和8200-1302。
下面的選項圖表顯示了差異零件號之間。
本手冊第1卷提供了安裝說明，描述控件，并解釋配置（編程）和操作程序。
第2卷包括關于將控件應用于特定應用程序、服務模式信息和505硬件規格。
本手冊不包含完整的操作說明汽輪機系統。
Electrostatic Discharge Awareness
Follow these precautions when working with or near the control. 1. Avoid the build-up of static electricity on your body by not wearing clothing made of synthetic materials. Wear cotton or cotton-blend materials as much as possible because these do not store static electric charges as much as synthetics. 2. Do not remove the printed circuit board (PCB) from the control cabinet unless absolutely necessary. If you must remove the PCB from the control cabinet, follow these precautions: ? Do not touch any part of the PCB except the edges. ? Do not touch the electrical conductors, the connectors, or the components with conductive devices or with your hands. ? When replacing a PCB, keep the new PCB in the plastic antistatic protective bag it comes in until you are ready to install it. Immediately after removing the old PCB from the control cabinet, place it in the antistatic protective bag.
The 505 Digital Control is suitable for use in European Zone 2, Group IIC environments when installed in an IP54 minimum rated enclosure per s EN 60079-0 and EN 60079-15. This equipment must be installed in an area or enclosure providing adequate protection against impact greater than 2 Joules and the entry of dust or water. For ATEX/IECEx the 505 Digital Control shall be installed in an enclosure that is coded Ex nA, providing a minimum IP54 ingress protection. The installer shall ensure that the maximum surrounding air temperature does not exceed the rated temperature of +70 °C at the final installation location. The 505 Digital Control shall not be installed in areas exceeding Pollution Degree 2 as defined in IEC 60664-1. The interior of the enclosure shall not be accessible in normal operation without the use of a tool.
Special Conditions for Safe Use
A fixed wiring installation is required. Field wiring must be in accordance with North American Class I, Division 2 (CEC and NEC), or European Zone 2, Category 3 wiring methods as applicable, and in accordance with the Local Inspection Authority having jurisdiction. Field wiring must be suitable for at least 10 °C above ambient conditions during operation. Grounding of the 505 Digital Control is required using the PE terminal. A switch or circuit breaker shall be included in the building installation that is in close proximity to the equipment and within easy reach of the operator. The switch or circuit breaker shall be clearly marked as the disconnecting device for the equipment. The switch or circuit breaker shall not interrupt the Protective Earth (PE) conductor.
This manual describes the Woodward 505 Digital Governor for steam turbines with single or split-range actuators. Released versions are 8200-1300, 8200-1301, and 8200-1302. The option charts below show the differences between the part numbers. Volume 1 of this manual provides installation instructions, describes the control, and explains the configuration (programming) and operating procedures. Volume 2 includes notes on applying the control to specific applications, Service mode information, and 505 hardware specifications. This manual does not contain instructions for the operation of the complete turbine system. For turbine or plant operating instructions, contact the plantequipment manufacturer.
公司主營產品圖展示
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營產品文字介紹
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃?xì)獍l(fā)電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
