REXROTH FWA-ECODR3-SMT-01VRS-MS伺服驅動器
1.產 品 介 紹
品牌：REXROTH
型號說明：REXROTH FWA-ECODR3-SMT-01VRS-MS伺服驅動器
優勢：供應進口原裝正品，專業停產配件。
公司主營特點：主營產品各種模塊/卡件，控制器，觸摸屏，伺服驅動器。
2.產 品 詳 情 資 料：
REXROTH FWA-ECODR3-SMT-01VRS-MS注：某些版本的控制器（組件編號為01-W3960Bxxx的控制器）可能具有J24工廠硬接線，位于8MHz位置，J2引腳1和2之間的縫釘隱藏在IP模塊下方。將出廠設置更改為32MHz設置需要移除引腳1和2之間的縫釘，并在引腳2和3之間安裝跳線。IP總線選通頭（J25）一些IP總線實現使用選通*信號（引腳46）作為來自IP2芯片的IP模塊的輸入。其他IP接口要求斷開選通。REXROTH FWA-ECODR3-SMT-01VRS-MS通過在J25引腳1和2之間安裝跳線，可編程頻率源連接到IP總線上的Strobe*信號。有關更多信息，請參閱《MVME162FX嵌入式控制器程序員參考指南》中的IP2芯片編程模型。如果從J25中移除跳線，則選通線路可用于IP模塊之間的邊帶類型的消息傳遞。Strobe*信號未連接到板上的任何有源器件，但可以連接到上拉電阻器。REXROTH FWA-ECODR3-SMT-01VRS-MS
Note Some versions of the controller (those identified with assembly number 01-W3960Bxxx) may have J24 factoryhardwired in the 8MHz position with a staple between J2 pins 1 and 2, hidden beneath an IP module. Changing the factory setting to the 32MHz setting requires removal of the staple between pins 1 and 2, and installation of a jumper between pins 2 and 3.REXROTH FWA-ECODR3-SMT-01VRS-MSIP Bus Strobe Select Header (J25) Some IP bus implementations make use of the Strobe? signal (pin 46) as an input to the IP modules from the IP2 chip. Other IP interfaces require that the strobe be disconnected. With a jumper installed between J25 pins 1 and 2, a programmable frequency source is connected to the Strobe? signal on the IP bus. Refer to the IP2 chip programming model in the MVME162FX Embedded Controller Programmer’s Reference Guide for additional information. If the jumper is removed from J25, the strobe line is available for a sideband type of messaging between IP modules. The Strobe? signal is not connected to any active devices on the board, but it may be connected to a pull-up resistor.REXROTH FWA-ECODR3-SMT-01VRS-MS
3.產 品 展 示
4.公 司 優 勢 主 營 產 品
5.相 關 產 品 展 示
本篇文章出自瑞昌明盛自動化設備有限公司官網，轉載請附上此鏈接:http://www.215pk.com
