REXROTH RMA02.2-32-DC024-050伺服模塊
1.產 品 介 紹
品牌：REXROTH
型號說明：REXROTH RMA02.2-32-DC024-050伺服模塊
優勢：供應進口原裝正品，專業停產配件。
公司主營特點：主營產品各種模塊/卡件，控制器，觸摸屏，伺服驅動器。
2.產 品 詳 情 資 料：
REXROTH RMA02.2-32-DC024-05模塊安裝在安裝了EPROM、IndustryPack和SIMM并正確配置了收割臺的情況下，按照以下步驟將REXROTH RMA02.2-32-DC024-05:1。關閉所有設備電源并斷開電源線與交流電源的連接！注意：為防止損壞模塊組件，請勿在通電時插入或移除模塊！警告：本設備中存在可能導致死亡的危險電壓。在處理、測試和調整時要格外小心。2.按照用戶手冊中的說明卸下機箱蓋。REXROTH RMA02.2-32-DC024-053.從要安裝控制器的卡插槽中卸下填充面板。–如果您打算將MVME162FX用作系統控制器，它必須占用最左側的卡插槽（插槽1）。系統控制器必須位于插槽1中，以正確啟動總線授權菊花鏈，并確保IACK菊花鏈驅動程序正常運行
REXROTH RMA02.2-32-DC024-05 Module Installation With EPROM, IndustryPack, and SIMMs installed and headers properly configured, proceed as follows to install the REXROTH RMA02.2-32-DC024-05 in the VME chassis: 1. Turn all equipment power OFF and disconnect the power cable from the AC power source. ! Caution To prevent damage to the module components, do not insert or remove modules while power is applied. ! Warning Dangerous voltages, capable of causing death, are present in this equipment. Use extreme caution when handling, testing, and adjusting. 2. Remove the chassis cover as instructed in its user’s manual. 3. Remove the filler panel from the card slot where you are going to install the controller. – If you intend to use the MVME162FX as system controller, it must occupy the leftmost card slot (slot 1). The system controller must be in slot 1 to correctly initiate the bus-grant daisy-chain and to ensure proper operation of the IACK daisy-chain driverREXROTH RMA02.2-32-DC024-05
3.產 品 展 示
4.公 司 優 勢 主 營 產 品
5.相 關 產 品 展 示
本篇文章出自瑞昌明盛自動化設備有限公司官網，轉載請附上此鏈接:http://www.215pk.com
