RELIANCE MC-D5006-A模塊卡件
1.產 品 詳 情 資 料：
RELIANCE MC-D5006-A1.將包含要傳輸?shù)捻?xiàng)目的CPU置于運行模式或停止模式。2.如果PME與RX3i聯機，則轉到脫機或選擇監視器模式。3.將RDSD插入CPU上的USB接口。（1-2秒后，RDSD指示燈變?yōu)榫G色。）4。對于CPE305/CPE310，向左推動RDSD方向開關（UPLOAD），然后瞬間按下START（啟動）按鈕。對于CPE330，按下RDSD UPLD按鈕。5.在傳輸過程中，RELIANCE MC-D5006-A請勿從CPU中取出RDSD。? 傳輸過程中，RDSD指示燈呈綠色閃爍。根據項目數據的大小RELIANCE MC-D5006-A，這可能需要10到150秒的時間。? RDSD指示燈應變?yōu)榫G色，表示傳輸已成功完成。? 如果RDSD指示燈變?yōu)榧t色，則表示傳輸失敗。在RDSD上嘗試傳輸結束時，將有一份故障表的副本。將RDSD插入裝有PACS Analyzer軟件的PC中，并在RDSD上選擇plcfaultafter.dat文件，以便分析儀進行故障表分析RELIANCE MC-D5006-A
RELIANCE MC-D5006-A1. Place the CPU that contains the project to be transferred in RUN Mode or STOP Mode. 2. If PME is online with the RX3i, either go Offline or select Monitor mode. 3. Insert the RDSD into the USB connector on the CPU. (After 1 – 2 sec,RELIANCE MC-D5006-A the RDSD LED turns solid green.) 4. For CPE305/CPE310, push the RDSD direction switch to the left (UPLOAD), then momentarily depress the START pushbutton. For CPE330, depress the RDSD UPLD pushbutton. 5. Do not remove the RDSD from the CPU during the transfer.RELIANCE MC-D5006-A? The RDSD LED blinks green during the transfer. This can take from 10 – 150 sec, depending upon the size of the project data. ? The RDSD LED should turn solid green, indicating that the transfer completed successfully. ? If the RDSD LED turns solid red, the transfer has failed. There will be a copy of the fault tables as they existed at the end of the attempted transfer on the RDSD. Insert the RDSD into a PC which has the PACS Analyzer software and select the plcfaultafter.dat file on the RDSD for fault table analysis by the AnalyzerRELIANCE MC-D5006-A
2.產 品 展 示
3. 主 營 產 品
本篇文章出自瑞昌明盛自動化設備有限公司官網，轉載請附上此鏈接:http://www.215pk.com
